Effect of aging and manufacturing tolerances on multi-stage transonic axial compressor performance

Document Type : Research Paper

Authors

1 Research and Optimization Division at Fartak Company (MIDHCO), Tehran, Iran

2 School of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran

Abstract

The Axial compressor is an integrated part of a gas turbine. The central part of compressors is its blades. Blade aerodynamic has a significant effect on compressor performance. Because of the adverse pressure gradient in the compressor, any deviation in the blade profile has a significant influence on the flow field as well as the compressor performance. During the manufacturing and operation of a compressor, the blade profile may deviate from the nominal design. This deviation may happen within the manufacturing process, e.g., changing in stagger angle of the blade, changing in the maximum thickness of the blade profile or may occur in an operation process, e.g., increasing the blade surface roughness. By the way, these deviations affect the compressor performance. In this research, a numerical investigation is carried out to understand better the effects of geometry variability of the blades, including maximum thickness, blade surface roughness, and rotor blades stagger angle on the Transonic Axial compressor performance parameters, including the efficiency and pressure ratio. A CFD code, which solves the Reynolds-averaged Navier–Stokes equations, is employed to simulate the complicated 3D flow field of the axial compressor. The code is validated against experimental data for the axial compressor. The numerical result is in good agreement with the test dataand error at the design point for the efficiency was computed to be 0.3%, which shows high accuracy of the numerical method. Then, the effect of geometry variability on the axial compressor blade performance parameters is studied. Results show that increase in the surface roughness, blade thickness, and the rotor blades twist lowers the efficiency, pressure ratio and mass flow significantly in the compressor. Results show with a 10% increase of the blade installation angle at the design point, the mass flow rate decreases 1.93%, and the efficiency and pressure ratio decreases 0.35% and 1.8%, respectively. The blade surface roughness reduces the mass flow rate, total pressure ratio and efficiency of the compressor. The results show that imposing the roughness at the design point of the compressor, mass flow rate and efficiency is reduced 1.8% and 2.75 %, respectively. Meridional view of this compressor is shown in figure 1 in which the blade profiles for the first to fourth stages are DCA type [1].

Keywords


[1] Hirsch, Ch., Denton, J. D.,” Propulsion and Energetic panel working group 12 on Through flow calculations in Axial Turbomachines”, AGARD Advisory Report No.175, Advisory group for Aerospace research and development. ADA109292, 1981.
[2] Gu, F., Engeda, A., Cave, M. and Di Liberti, L., "A Numerical Investigation on the Volute/Diffuser Interaction Due to the Axial Distortion at the Impeller Exit," Transactions of the ASME, Journal of Fluid Engineering, Vol. 123, no. 3, pp. 475-483, 2001.
[3] Mugli, F., Holbein, P. and Dupont, P., "CFD Calculation of a Mixed Flow Pump Characteristic from Shut-off to Maximum Flow", in Proc. ASME Fluid Engineering Division Summer Meeting (FEDSM'01), New Orleans, LA, USA, paper FEDSM2001-18072, May-June 2001.
[4] Cravero, C. and Marini, M., "Modeling of Incompressible Three-Dimensional Flow in Rotating Turbomachinery Passages", in Proc. ASME Fluids Engineering Division Summer Meeting (FEDSM'02), Montreal, Quebec, Canada, paper FEDSM2002-31177, July 2002.
[5] K. L Suder, R. V. Chima, A. J. Strazisar, W. B. Roberts, "The Effect of Adding Roughness and Thickness to a Transonic Axial Compressor Rotor", Journal of Turbomachinery. Vol. 117/491, 1995.
[6] Syverud, E., Brekke, O., and Bakken, L.  E., “Axial Compressor Deterioration Caused by Saltwater Ingestion”, ASME J. Turbomach., 129, pp. 119–127,2007.
[7] Ferziger, J.H. and Peric, M., "Computational Methods for Fluid Dynamics", Springer, Berlin, Germany,1996.
[8] ANSYS CFX-11 User's Guide
[9] Budugur Lakshminarayana,"Fluid dynamics and Heat transfer of Turbomachinery", JohnWiley & Sons Inc, ISBN 0-471-85546-4, 1996.
[10] Jessica M., Walker,  Karen, A., Flack, Ethan E.Lust, Michael P.Schultz and LuksaLuznik. "Experimental and numerical studies of blade roughness and fouling on marine current turbine performance "Renewable Energy, Volume 66, June 2014, Pages 257-267
[11] Luis Priegue and Thorsten Stoesser "The influence of blade roughness on the performance of a vertical axis tidal turbine"International Journal of Marine Energy, Volume 17 (2017), Pages 136–146
[12] Bouhelal Abdelhamid, Arezki Smaïli, Christian Masson and Ouahiba Guerri "Effects of Surface Roughness on Aerodynamic Performance of Horizontal Axis Wind Turbines" The 25th Annual Conference of the Computational Fluid Dynamics Society of Canada, CFD2017-337, 18-21 June 2017, University of Windsor.
[13] Marco Montis, Reinhard Niehuis, Mattia Guidi, Simone Salvadori, Francesco Martelli, and Bruno Stephan 2009, "Experimental and Numerical Investigation on the Influence of Trailing Edge Bleeding on the Aerodynamics of a NGV Cascade", in Proc. ASME Turbo Expo, GT 2009-59910.
[14] Nili-Ahmadabadi M., Hajilouy-Benisi A., Durali M., F. Ghadak.,2008 “Investigation of a Centrifugal Compressor and Study of the Area Ratio and Tip Clearance Effects on Performance” Journal of thermal science.
[15] Dwain. D, Glen S. 2009, “Turbulence Model Comparisons for a Low Pressure 1.5 Stage Test Turbine” ISABE-2009.
[16] Benini.B, Biollo.R, 2007, “Aerodynamics of swept and leaned transonic compressor-rotors”, Journal of Applied energy pp. 1012–1027
[17] Mugli, F., Holbein, P. and Dupont, P., May-June 2001, "CFD Calculation of a Mixed Flow Pump Characteristic from Shut-off to Maximum Flow," in Proc. ASME Fluid Engineering Division Summer Meeting (FEDSM'01), New Orleans, LA, USA, paper FEDSM2001-18072.
[18] Roland. H. Aungier, 2003, " Axial Flow Compressors: A Strategy for Aerodynamic Design and Analysis ", American Society of Mechanical Engineers, ISBN-10: 0791801926.